人狗畜禽COMPANY LIMITED|全是肉的高H文〈男男〉|全篇肉高H秘书被C办公室四爱|全黄H全肉共妻|全黄H全肉短篇禁乱NP慕浅浅|全黄H全肉短篇N男男

技術熱線: 4007-888-234
設計開發

專注差異化嵌入式產品解決方案 給智能產品定制注入靈魂給予生命

開發工具

提供開發工具、應用測試 完善的開發代碼案例庫分享

技術支持

從全面的產品導入到強大技術支援服務 全程貼心伴隨服務,創造無限潛能!

新品推廣

提供新的芯片及解決方案,提升客戶產品競爭力

新聞中心

提供最新的單片機資訊,行業消息以及公司新聞動態

串口驅動繼電器

更新時間: 2019-03-23
閱讀量:1989


串口驅動繼電器

Parallel Port Relay Interface



           Below are three examples of controlling a relay from the PC's parallel printer port (LPT1 or LPT2). Figure A shows a solid state relay controlled by one of the parallel port data lines (D0-D7) using a 300 ohm resistor and 5 volt power source. The solid state relay will energize when a "0" is written to the data line. Figure B and C show mechanical relays controlled by two transistors. The relay in figure B is energized when a "1" is written to the data line and the relay in figure C is energized by writing a "0" to the line. In each of the three circuits, a common connection is made from the negative side of the power supply to one of the port ground pins (18-25).



           There are three possible base addresses for the parallel port You may need to try all three base addresses to determine the correct address for the port you are using but LPT1 is usually at Hex 0378. The QBasic "OUT" command can be used to send data to the port. OUT, &H0378,0 sets D0-D7 low and OUT, &H378,255 sets D0-D7 high. The parallel port also provides four control lines (C0,C1,C2,C3) that can be set high or low by writing data to the base address+2 so if the base address is Hex 0378 then the address of the control latch would be Hex 037A. Note that three of the control bits are inverted so writing a "0" to the control latch will set C0,C1,C3 high and C2 low.

师宗县| 称多县| 修武县| 尼勒克县| 社会| 东阿县| 长葛市| 钦州市| 祁东县| 丰台区| 余姚市| 甘孜县| 江安县| 萨嘎县| 武宣县| 固始县| 苏尼特右旗| 玉山县| 东乡| 比如县| 黄骅市| 江安县| 阿合奇县| 崇左市| 勐海县| 婺源县| 香格里拉县| 新化县| 香河县| 隆回县| 巴东县| 南漳县| 兴安盟| 宜川县| 廊坊市| 黄骅市| 平湖市| 鄂尔多斯市| 镇安县| 宕昌县| 汶川县|